Action & Trigger Components

586-brass-escutcheon 488-22-45-mag-ejector 29-mkii-mkiii-trigger 595-silver-llv 603-gold-tg2000 48-mkii-mkiii-accurizing-kit 604-blue-tg2000 620-22-45-frame 384-firing-pin

TG2000

594-tg2000-colors

The TG2000 is a complete CNC-machined trigger guard equipped with precision EDM parts providing a crisp, clean 2lb trigger pull!

It features both pretravel and overtravel adjustments that can be adjusted by the shooter to their individual preference.

This match trigger guard is CNC-machined from a solid billet of high strength aircraft aluminum. The hammer, sear and disconnector are precision wire EDM-cut from A2 hardened tool steel with tolerances being held to +/- .0002" assuring every trigger let off to be extremely consistent. The CNC-machined trigger is hard black anodized.

The trigger is reset internally to eliminate any dragging or inconsistencies caused by a conventional tr … (more details).

Replacement Receiver

220-ss-receiver-w-picatinny-mount

Are you looking for an affordable way to start building a high quality semi-auto 22 LR, look no further than the Volquartsen Replacement Receivers for the Ruger 10/22. Our receivers are CNC-machined (no castings) from a solid billet of either aircraft quality aluminum or 416 stainless steel. The alloy receiver is then hard anodized to provide for years of enjoyable shooting!!

The CNC-machining process eliminates the burrs and rough surfaces that can be found in cast receivers. These burrs can create a drag on the bolt which can affect the performance of the rifle. The receiver is designed to be used with both Ruger factory bolts and trigger guards or, for the ultimate shooting performa … (more details).

CNC-Machined Bolt for 10/22

613-cnc-machined-bolt-silver

Complete CNC-Machined Bolt features our hardened and tuned extractor for positive, consistent extraction. It also includes our round titanium firing pin. This round design eliminates the unnecessary movement found on most 10/22 firing pins. The CNC-machining process allows us to hold the head spacing to exact dimensions eliminating the need for having your factory bolt reworked.

Bolt is case hardened and then a black nitride finish applied for improved lubricity during cycling. Ejection port side of the bolt is then polished.

Specs

  • Recoil rod and spring designed specifically for this bolt included
  • Recoil buffer included
  • 6oz base weight

Bolt Tune-Up Kit for Ruger 10/22

408-10-22-bolt-tune-up-kit

The Volquartsen Bolt Tune-Up Kit for the Ruger 10/22 (22 LR model only) rifle contains two of our most popular items ever: the Exact Edge Extractor and our SureStrike Firing Pin. This kit is designed to eliminate light hits and stovepipes.

Extended Bolt Handle and Recoil Rod Assembly for 10/22

154-10-22-extended-bolt-handle-black

The Extended Bolt Handle features the same shape and design as the bolt handle featured on our fully machined bolts. This handle has also been extended .25" for faster, easier operation. The recoil rod is polished, hardened and coated with a proprietary finish. This finish is not only extremely hard, but also contains lubricating features to create an extremely smooth operating guide rod. This coated recoil rod reduces friction which improves both feeding and ejecting. A recoil rod spring is also included. This spring has been cryogenically treated to withstand years of use.

Brass Escutcheon

586-brass-escutcheon

Machined escutcheon designed for 10/22 style stocks. Features straight knurl on the body for superior fit.

Specs

  • .625" OD
  • .375" thickness
  • .250" through hole with .380" counterbore diameter .140" deep

HP Action Kit

38-10-22-hp-action-kit

This kit consists of our target hammer (includes shims and bushings), hammer spring, target disconnector, target sear and target trigger Includes polished plunger and spring) with overtravel adjustment. Also included is a recoil buffer to reduce wear on the action and bolt. The HP Action Kit will give the shooter one of the most crisp, clean trigger pulls available. Reduces trigger pull down to approximately 2.25 – 2.5lbs.

HP Action Kit Plus features our High Performance Kit, Extended Magazine Release and Auto Bolt Release.

Black or Silver option is only applicable to HP Action Kit Plus.

Match Hammer and Sear for 10/22 and 10/22 Magnum

159-10-22-match-hammer-sear

Includes a target hammer and target sear. Both the hammer and sear are wire EDM-cut for exacting tolerances. Both parts are then hardened to a Rc 58-60. It also includes hammer shims and bushings. Reduces trigger pull down to approximately 2.25 – 2.5lbs.

V-Locking Block for 10/22 and 10/22 Magnum

346-10-22-v-block

Volquartsen CNC-machined 10/22 V-Locking Block for improved performance and accuracy. This part is machined from stainless steel and then hardened to Rc 40-42. The combination of stainless steel and the heat treating process results in an extremely rigid and durable locking block! No more worrying about over tightening the retaining screws and cracking the factory issued V-Block.

Extended Magazine Release for MKII

46-mkii-ext-magazine-release

Provides extended length over the factory magazine release for faster, easier magazine changes. It is designed to work with oversized target style grips. Drop-in part that requires no gunsmithing. This magazine release is CNC-machined from 416 stainless steel billet material. No casting!! Fits Ruger MKII only.

Extended Magazine Release for MKIII

610-mkiii-extended-mag-release

The MKIII Extended Magazine Release is an 1/8" longer than the factory release providing easier access. This release has also been modified to improve insertion of the factory magazines.

Specs

  • CNC Machined from stainless
  • Designed for the Ruger MKIII steel frame

Extended Safety for MKII, MKIII or MKIII 22/45

434-mkiii-extended-safety

The Extended Safety provides the shooter improved access to the safety on the Ruger MKII, MKII 22/45, MKIII and MKIII 22/45 pistol. The Extended Safety is the perfect addition when being used with target grips. The contour is wire EDM precision cut from 17-4 stainless steel. The Extended Safety is .150" longer than the factory button. Comes complete with safety detent and spring.

Please note that the Ruger MKII 22/45 requires a different safety and is available in black only.

Extended Bolt Release for MKII and MKIII

37-mkii-mkiii-silver-ext-bolt-release

Replaces the factory bolt release in minutes and provides the shooter with a .375" serrated face for an easier release of the bolt. Fits both the Ruger MKII and MKIII. Not compatible with the 22/45.

VC Mainspring for Ruger Pistols

600-stainless-mainspring-housing

Complete mainspring assembly designed for the Ruger MKII or MKIII. Mainspring components are wire EDM-cut and CNC-machined.

Our mainspring does not feature the lock feature found on the Ruger factory MKIII Mainspring.

Specs

  • Models available for either the Ruger MKII/MKIII or the 22/45
  • 2oz base weight

Target Sear for MKII and MKIII

15-mkii-mkiii-target-sear

This specially designed sear provides the shooter with a shorter, faster, cleaner breaking trigger pull. The sear is wire EDM-cut from hardened A2 tool steel. Fits Ruger MKII, MKIII and 22/45.

Oversized Safety for 10/22 and 10/22 Magnum

52-10-22-oversized-safety

Safety design for either a right or left handed shooter. Features an oversized head for easier access. May require slight modification to stock for installation. Fits both Ruger 10/22 LR and 10/22 Magnum rifles.

Exact Edge Extractor for High Standard

163-high-standard-exact-edge-extractor

The Exact Edge Extractor is manufactured through an EDM process to produce exacting tolerances. The new extractor will not lose its edge under impact such as other extractors made from stamped steel or titanium that will have their edges roll over and actually cause extraction problems after a short period of use. Our extractor features a very precise hook point. It is hardened to a Rc 58-60 to withstand years of use and still maintain its edge. We are able to hold the tolerances to +/-.0001" by utilizing the EDM manufacturing process. The hook is .005" closer to the rim of the cartridge to allow for the most positive extraction available. Made of A2 tool steel.

Competition Bolt for Ruger MKII or MKIII

550-extended-bolt

Are you a competitive shooter looking to eliminate stovepipes, failures to fire and improve the overall performance of your Ruger MKII or MKIII pistol? The Competition Bolt is the answer!

The Competition Bolt is CNC-machined and ground for superior tolerances, fit and finish. It features an Exact Edge Extractor as well as the SureStrike Firing Pin.

The Competition Bolt has an integral Extended Bolt Racker to allow for improved manual cycling of the bolt – no more pinched fingers!

Specs

  • Available in either a black nitride or silver hard chrome finish
  • 4oz base weight

Safety for 10/22 and 10/22 Magnum

166-10-22-safety

CNC-machined hardened steel.

CNC-Machined Disconnector for MKII and MKIII

609-mkii-disconnector

Our CNC-Machined Disconnector is CNC-machined from 416 stainless steel. The machining process allows us to make several design changes to the the way the disconnector functions. We have added material that increases rigidity over the current design. This increased rigidity not only improves trigger pull but also will improve overall functioning as it will prevent any binding or interference that can be found on the prior design and factory design. This is due, in part, to variances in the factory frame tolerances.

The CNC-machined design also features an integral pin without the step found on the factory design. We have also machined the pin that comes in contact with the trigger plunge … (more details).

Spring-Loaded Magazine Ejector for 22/45

488-22-45-mag-ejector

Our Spring-Loaded Magazine Ejector for the Ruger 22/45 will improve the mag drop of the factory magazine. Its unique design uses spring pressure to forcefully remove the magazine from the grip frame. The innovative design not only aids in magazine removal but also adds an extension to the bottom of the magazine to make magazine reloads quick and reliable every time.

The ejector is CNC-machined from an aluminum alloy and black hard anodized. Also features a CNC-machined stainless steel button for increased durability.

Simply remove the magazine floor plate from a factory 22/45 magazine and replace with this ejector for an enhanced shooting experience!

Target Trigger for MKII and MKIII

29-mkii-mkiii-trigger

CNC-machined Target Trigger features both pretravel and overtravel adjustments.

Bolt Tune-Up Kit for MKI, MKII and MKIII

385-bolt-tune-up-kit

The Volquartsen Bolt Tune-Up Kit for the Ruger MKI, MKII and MKIII target pistols contains one of our most popular items ever, the Exact Edge Extractor and our SureStrike Firing Pin.

This kit is designed to eliminate light hits and stovepipes.

Accurizing Kit

48-mkii-mkiii-accurizing-kit

Complete drop-in kit comes complete with Target Hammer, Target Sear, Target Trigger (available in either black hard anodized aluminum or optional stainless steel), Extended Bolt Release and Trigger Return Spring with Polished Plunger. The trigger features adjustable pretravel and overtravel screws.

The Accurizing Kit combines all of the internal components needed for that crisp, clean 2.25lb trigger pull the discriminating shooter is looking for. No stoning or fitting required. Final trigger pull may vary slightly due to factory frame variances.

Specs

  • Accurizing Kits fit the Ruger MKII, MKIII and all variations of the 22/45 (extended bolt release and sear spring are not used when installing in a 22/45).
  • MKII Kit also includes a MKII Hammer Bushing and can be used in the MKIII in order to eliminate the magazine disconnect.
  • The color option applies only to the Extended Bolt Release.

Target Hammer for MKII and MKIII

9-mkiii-target-hammer

The MKII and MKIII Target Hammer is a complete drop-in item that is wire EDM-cut from hardened tool steel. The target hammer will not only reduce your trigger pull but will also improve lock time. Fits MKII, MKIII, and 22/45

Hammer Bushing for MKII

338-mkii-hammer-bushing

MKII Hammer Bushing manufactured by screw machine equipment. The hammer pivot pinhole has been drilled and reamed for improved precision to help eliminate variances that can be found in the factory bushing. Black oxide finish and hardened.

This bushing is compatible with a MKII Hammer only. It can be used in conjunction with a MKII Hammer to eliminate the magazine disconnect in the MKIII pistol.


Cross Reference

A02505

VC Target Frame

441-vc-target-frame-red

The VC Target Frame is CNC-machined from aluminum alloy. It is a complete frame with the following features: Accurizing Kit (includes Extended Bolt Release, CNC-machined Target Trigger, wire EDM-cut Target Hammer and Target Sear), CNC-Machined Disconnector, Built-in Spring-Loaded Magazine Ejector (MKIII model only) and Extended Safety. The VC Frame is shipped with a clean, crisp 2.25lb trigger pull. The magazine disconnect has also been eliminated from this frame.

The VC Target Frame is available in two grip angle configurations. Several grip options are also available: Volthane Target Grips (MKIII style only), Laminated Wood Target Grips (MKIII style only), Aluminum Grips or the Ho … (more details).

Exact Edge Extractor for Remington 597

162-remington-597-exact-edge-extractor

The Exact Edge Extractor is manufactured through an EDM process to produce exacting tolerances. The new extractor will not lose its edge under impact such as other extractors made from stamped steel or titanium that will have their edges roll over and actually cause extraction problems after a short period of use. Our extractor features a very precise hook point. It is hardened to a Rc 58-60 to withstand years of use and still maintain its edge. We are able to hold the tolerances to +/-.0001" by utilizing the EDM manufacturing process. The hook is .005" closer to the rim of the cartridge to allow for the most positive extraction available. Made of A2 tool steel.

Target Hammer for Remington 597

30-remington-597-target-hammer

It is a wire EDM-cut, fully machined (no casting or stampings) hammer. It will provide a 50% (approx) lighter trigger pull. It is a drop-in item designed to be used in an unaltered factory trigger guard. Made of A2 tool steel, hardened to Rc 58-60. Fits the Remington 597 22LR, 22 WMR and 17 HMR.

Exact Edge Extractor for Walther P22

195-walther-p22-extractor

The Exact Edge Extractor is manufactured through an EDM process to produce exacting tolerances. The new extractor will not lose its edge under impact such as other extractors made from stamped steel or titanium that will have their edges roll over and actually cause extraction problems after a short period of use. Our extractor features a very precise hook point. It is hardened to a Rc 58-60 to withstand years of use and still maintain its edge. We are able to hold the tolerances to +/-.0001" by utilizing the EDM manufacturing process. The hook is .005" closer to the rim of the cartridge to allow for the most positive extraction available. Made of A2 tool steel.

Spring Kit for MKI, MKII, and MKIII

171-mkii-mkiii-spring-kit

Reduced power trigger plunger and mainspring. Also includes assembly pin for ease of installation on the mainspring. Fits Ruger MKI, MKII, MKIII and 22/45.

Want us to install the mainspring into the mainspring housing latch? Add our VC2SK-Install to your order.

Specs

  • Mainspring installation may require gunsmithing

SureStrike Firing Pin for MKI, MKII, and MKIII

384-firing-pin

Volquartsen SureStrike Firing Pin is designed to minimize and/or eliminate light hits on the Ruger MKI, MKII and MKIII (including 22/45) pistol. The SureStrike Firing Pin is precision EDM machined from A2 tool steel. The impact section of the firing pin is then surface ground to create the optimal “SureStrike” each and every time!

This new firing pin is also .004" wider than the factory firing pin to help eliminate side to side movement in the factory bolt.

Hardened to a Rc 56-58 to prevent any excessive wear and deformation that can be found on the factory firing pin. The hardening process on the A2 material allows for a much deeper hardening when compared to conventional cas … (more details).

Hammer Spring/Strut Assembly for 10/22 and 10/22 Magnum

398-spring-strut-assembly

Our reduced power 10/22 hammer spring is manufactured by the leader in high quality gunsprings, Wolff Gunsprings. We have added a Nylon 11 coating to the spring to create the best 10/22 hammer spring on the market. The Nylon 11 coating is tough and extremely resistant to abrasion, wear and impact. It also has a low coefficient of friction along with good solvent and chemical resistance. This spring is designed to last! Volquartsen offers a lifetime warranty on this spring.

Spring comes complete installed on a Volquartsen hammer strut. This provides for a very quick, simple installation. The hammer strut has also been polished on the critical bearing areas to help eliminate drag d … (more details).

Hammer Spring with Nylon 11 Coating for 10/22 and 10/22 Magnum

Our reduced power 10/22 hammer spring is manufactured by the leader in high quality gunsprings, Wolff Gunsprings. We have added a Nylon 11 coating to the spring to create the best 10/22 hammer spring on the market. The Nylon 11 coating is tough and extremely resistant to abrasion, wear and impact. It also has a low coefficient of friction along with good solvent resistance. This spring is designed to last! Volquartsen offers a lifetime warranty on this spring.

Also available already installed on polished strut. Part #VC10SA

SureStrike Firing Pin for Ruger 10/22

409-1022-firing-pin

Volquartsen SureStrike Firing Pin is designed to minimize and/or eliminate light hits on the Ruger 10/22 (22 LR model only). The SureStrike Firing Pin is precision EDM machined from A2 tool steel. The impact section of the firing pin is then surface ground to create the optimal “SureStrike” each and every time!

This new firing pin is also .004" wider than the factory firing pin to help eliminate side to side movement in the factory bolt.

Hardened to a Rc 56-58 to prevent any excessive wear and deformation that can be found on the factory firing pin. The hardening process on the A2 material allows for a much deeper hardening when compared to conventional case hardening.

Install HP Action Kit

Volquartsen will professionally install your HP Action Kit. There is no need to take it to a gunsmith, simply send us your trigger guard and it will generally be on its way back to you in 10-14 days. Price includes return shipping of your trigger guard only.

Gun Guide for MKIII

215-mkiii-gun-guide

Complete disassembly & reassembly guide for the Ruger MKIII pistol (includes the Standard, Target Gov’t Target, Competition, Hunter and 22/45 Models). This book features 19 pages & 36 high-resolution grayscale images. This is the perfect tool for those customers looking for a little more information when performing aftermarket part installations or general maintenance on their Ruger MKIII.

Gun Guide for MKII

247-complete-22-pistols-book

RUGER .22 Automatic Pistols 1947 ~ 2004
For your Ruger Standard, Mark I, Mark II, 22/45, Competition, Government, Slab-sides and all special models prior to the release of the new Mark III series introduced in 2005.
So, you decided to disassemble your Mark pistol and now YOU CAN’T GET IT BACK TOGETHER AGAIN!

FEATURES:

  • The only CURRENT printed manual that includes information on
    ALL models from 1947 ~ 2004 (Mark I, Mark II, 22/45, etc.)
  • Contains most of the same text and high resolution graphics
    found in the CD-ROM program
  • Easy to use — lies open and flat on your work surface
  • 56 pages – 55 high-resolution grayscale images
  • Includes "rare … (more details).

Gun guide for 10/22

246-complete-10-22-book

A complete guide to the Ruger 10/22 featuring assembly and disassembly instructions and schematics.

FEATURES:

• The only current printed manual that includes information on
ALL models from 1964 ~ 2005.
• Includes all serial numbers and manufacture dates for
all models from 1964 ~ 2004!
• Easy to use – Comb binding lies open and flat on your work surface.
• 56 pages & 66 high-resolution grayscale images.
• Cardstock cover. Bright white paper.

Specs

  • 3oz base weight

Posi-Lock Bolt Latch for MKII and MKIII

596-mkiii-bolt-stop

Are you tired of having to replace your factory bolt hold open latch? Our new Posi-Lock Bolt Hold Open Latch has been engineered to withstand years of use for even the most demanding shooter.

Manufactured from hardened A2 tool steel this latch contacts the bolt in a more effective way in order to ensure the bolt locks open on each and every empty magazine.

Specs

  • Fits both the Ruger MKII and MKIII pistols (does not fit the 22/45 model)

Cross Reference

Replaces Ruger Part #AN-37

22 Short Kit for 10/22

Designed to convert a factory 10/22 22 LR to 22 Short. It includes a CNC-machined, hard anodized, alloy bolt, recoil rod with spring, modified magazine and a reduced hammer spring.

Specs

  • 4oz base weight

Automatic Bolt Release

39-10-22-silver-auto-bolt-release

Enables the shooter to simply pull bolt back slightly to release the bolt. This eliminates the need to push up on the bolt lock mechanism to release the bolt. This is an easy drop-in installation. Available in silver or black.

Exact Edge Extractor for 10/22 and 10/22 Magnum

44-exact-edge-extractor-for-10-22-and-mkii-mkiii

The Exact Edge Extractor is manufactured through an EDM process to produce exacting tolerances. The new extractor will not lose its edge under impact such as other extractors made from stamped steel or titanium that will have their edges roll over and actually cause extraction problems after a short period of use. Our extractor features a very precise hook point. It is hardened to a Rc 58-60 to withstand years of use and still maintain its edge. We are able to hold the tolerances to +/-.0001" by utilizing the EDM manufacturing process. The hook is .005" closer to the rim of the cartridge to allow for the most positive extraction available. Made of A2 tool steel.

Extended Magazine Release for 10/22 and 10/22 Magnum

32-10-22-silver-extended-magazine-release

The extended magazine release allows for a quick release of factory magazines. Simply reach in front of the trigger guard and push forward, no more having to push up on the factory release. It extends .550" down from the trigger guard housing designed not to interfere with benchrest or sandbags during shooting. The extended magazine release is completely CNC-machined from billet material – no castings!!

Hex-Head Take Down Action Screw for 10/22 and 10/22 Magnum

165-10-22-take-down-action-screw

Hex-head screw replaces the factory slotted screw. It allows the shooter to use a torque wrench for precise and repeatable settings. No more marred slotted screws which diminish the apperance of your rifle. Made of hardened alloy steel.

17 Mach2 Pistol Conversion

109-mkiii-17-mach-2-conversion

Looking to improve the capabilities of your Ruger MKII or Ruger MKIII pistol? Our Mach2 pistol conversion unit may be just what you are looking for. Simply drop in the Volquartsen Mach2 pistol conversion unit and transform your 22 LR pistol into a 17 Mach2. Our barreled action features a CNC-machined stainless steel receiver, match, digitally-gauged 8" barrel and a fully machined alloy bolt. There are no other modifications needed! The conversion is then fitted with a Weaver style scope mount for mounting the scope or red dot optic of your choice.

The Mach2 Pistol Conversion includes barreled receiver, bolt and mount. Factory frame and mainspring required to complete pistol build. … (more details).

Recoil Buffer for 10/22 and 10/22 Magnum

47-10-22-recoil-buffer

Drop-in polyurethane bolt stop pin eliminates the metal to metal contact between bolt and receiver and eliminates vibration caused by this. The recoil buffer also provides a remarkable difference in cycling noise. Replaces factory bolt stop pin.

Install MKII or MKIII Accurizing Kit or Pistol Competition Kit

Volquartsen will professionally install your Accurizing Kit or Pistol Competition Kit. There is no need to take it to a gunsmith, simply send us your frame and it will generally be on its way back to you in 10-14 days.

Extended Magazine Release for 77/22

112-77-22-ext-magazine-release-black

The extended magazine release allows for a quick release of factory magazines. Simply reach in front of the trigger guard and push forward, no more having to push up on the factory release. It extends .550” down from the trigger guard housing designed not to interfere with benchrest or sandbags during shooting. The extended magazine release is completely CNC-machined from billet material – no castings!!

Not compatible with the all-weather 77/22.

Target Disconnector for 10/22 and 10/22 Magnum

63-10-22-target-disconnector

Manufactured through an EDM process for exacting tolerances. Designed to be used in conjunction with match hammer and sear to provide for a very crisp, clean trigger pull. Made of A2 tool steel and hardened to Rc 58-60.

Target Hammer for 10/22 and 10/22 Magnum

164-10-22-target-hammer

Our redesigned target hammer is now wire EDM cut! The target hammer is designed to give the factory Ruger 10/22 a superb “trigger job” by simply replacing the factory hammer. No stoning or fitting is required. Reduces trigger pull down to approximately 2.5 – 2.75lbs. Made of stainless steel, hardened to Rc 58-60. Includes our 10/22 hammer spring, hammer bushings, hammer shims and trigger return spring.

Target Sear for 10/22 and 10/22 Magnum

62-10-22-target-sear

Manufactured through an EDM process for exacting tolerances for a crisp, light trigger pull. Drop-in item that requires no stoning. Made of A2 tool steel and hardened to Rc 58-60.

Target Trigger for 10/22 and 10/22 Magnum

167-10-22-target-trigger

Improved trigger design gives the shooter more trigger control. Also features an overtravel adjustment screw. Made of aluminum.

Volquartsen Firing Pin, Magnum

Replacement titanium firing pin designed to fit Volquartsen 22 WMR and 17 HMR rifles.

Volquartsen Firing Pin, Long Rifle

Replacement titanium firing pin designed to fit Volquartsen 22 LR and .17 Mach 2 rifles.

Volquartsen Extractor

This Exact Edge Extractor is designed to only fit Volquartsen manufactured bolts such as our VC10BLT, VC27BLT and any bolt from one of our complete rifles.

Volquartsen Bolt Handle

This is a replacement bolt handle for any Volquartsen rimfire rifle or Volquartsen CNC machined bolt. Designed to snap into place on a Volquartsen bolt but will not work on a Ruger Bolt.

Spring Loaded Plunger for Volquartsen Bolt

Spring loaded plunger designed to fit into the Volquartsen bolt. This plunger helps secure the bolt handle.

Recoil Buffer For Volquartsen Rifle

Recoil Buffer For VC Rifle.

Target Sear for 77/22

611-77-22-target-sear-edm

Easy to install Target Sear will reduce the trigger pull to approximately 1.5lbs. The target sear is wire EDM cut from hardened tool steel to eliminate any modification or fitting in most applications. Includes lighter trigger spring.

Specs

  • Fits, 22 LR, 22 WMR and 17 HMR.

LLV Competition Pistol Upper

492-llv-on-stainless-mkiii-frame

The LLV barreled receiver has been completely redesigned. A great design has been made even better – better balance, more versatile and, yes, even better accuracy!

A hard anodized CNC-machined billet receiver is the foundation of this lightweight setup. The receiver and barrel shroud are precision-machined as one piece from aluminum alloy. An integral Picatinny rail is machined into the top of the receiver. It is then fitted with either a 4.5" or 6" precision stainless steel barrel that has been machine-honed and lapped. The barrel has been contoured to reduce weight without sacrificing accuracy.

The LLV Competition Upper features a stainless steel breech face designed to withstan … (more details).

Exact Edge Extractor for MKII and MKIII

The Exact Edge Extractor is manufactured through an EDM process to produce exacting tolerances. The new extractor will not lose its edge under impact such as other extractors made from stamped steel or titanium that will have their edges roll over and actually cause extraction problems after a short period of use. Our extractor features a very precise hook point. It is hardened to a Rc 58-60 to withstand years of use and still maintain its edge. We are able to hold the tolerances to +/-.0001" by utilizing the EDM manufacturing process. The hook is .005" closer to the rim of the cartridge to allow for the most positive extraction available. Made of A2 tool steel. Fits the complete line of MKI … (more details).

Hammer Bushing for 10/22 (Package of 2)

A set of two 10/22 Hammer Bushings that have been manufactured on a Swiss screw machine. Our bushings have been redesigned to improve the overall trigger pull. One bushing features a longer shaft to give the hammer one pivot point instead of two found on the factory bushings.

All serial numbered items must be shipped to an FFL dealer.
All firearm orders require a $500 non-refundable deposit to initiate production.
Copyright ©2014 Volquartsen® Custom
Contact webmaster@volquartsen.com with website issues or suggestions.